At under 4" tall, our 3.5" round RGB and RGB + White LED recessed light can fit into tight spaces that a traditional recessed can light can’t, such as ceilings with ductwork/piping/obstructions, hot-roof ceilings with limited vertical clearance, and tight soffits.
These lights feature an easily adjustable LED face that can be pointed straight downward, making them compatible with sloped ceilings (up to 6/12 pitch or 26.57°). Our slope ceiling recessed lights also make perfect art spotlights or wall accent lights, as they can also be installed in flat ceilings and adjusted to point at walls, artwork, or sculptures.
Use the RGB Color Changing capability of these unique lights to create a truly unique aesthetic for your space.
Safety & Warnings
- Install in accordance with the National Electric Code, and all local regulations.
- This product is intended to be installed and serviced by a qualified licensed electrician.
- Only use with compatible LED fixtures, controls and dimmer switches. Only use copper wiring.
- Proper heat dissipation will prolong the working lifespan of this product. Install in well-ventilated area free from explosive gases and vapors.
- Ensure appropriate type and size wire is installed between driver, fixture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating, and type (in-wall rated, wet location rated, etc). Improper wire type could overheat wires, and cause a fire.
- Do not install if product has any visible damage.
- Do not modify or disassemble this product beyond instructions or the warranty will be void.
- Use only constant voltage fixture LED power supply.
|LED Light Color||Input Voltage||SKU||Dimensions||Cut-Out Hole Size|
|RGB||12VDC||AL-RL-S-35-U-12VDC-RGB||3.5" (89mm) diameter
2” (51mm) tall
|2.5" (63mm) diameter|
|RGB + Warm White||12VDC||AL-RL-S-35-U-12VDC-RGBWW||3.5" (89mm) diameter
3.9" (100mm) tall
|2.5" (63mm) diameter|
|RGB + Cool White||12VDC||AL-RL-S-35-U-12VDC-RGBCW||3.5" (89mm) diameter
3.9" (100mm) tall
|2.5" (63mm) diameter|
Tools You'll Need
- Tape measure
- Wire stripper
- Screw driver
- Drill with hole saw (optional)
Before You Begin
We know how boring it can be to read instructions, so we’ll keep this installation guide as short and sweet as possible. Before you begin with your installation, be sure to fully read these instructions. They contain many useful tips and pointers that will help to ensure a perfect installation, save you time, and ensure your safety.
It is important that you install this product (and all other electrical products) in accordance with the National Electric Code (NEC) and all applicable local building and electrical codes for your area. If you are unfamiliar with the NEC, your local building/electrical codes, and/or the proper installation methods for electrical devices, you should hire a qualified and licensed electrician to do the work for you.
Before doing any electrical work, always disconnect power at the fuse or circuit breaker
Planning your layout
Most electricians space recessed lights equally apart from each other forming a grid pattern on the ceiling. The distance between each light generally depends on the LED wattage of your light. Here are a few rough rules of thumb for spacing when using the lights as primary lighting (if you are using the lights as accent lighting or you have other lights in your room, you can space them further apart):
|LED Wattage||Incandescent Equivalent||Recommended Spacing|
|3 Watts||25 Watt||3W fixtures are generally used for accent/cabinet lighting and are not usually used as general room lighting. If you do use them as general lighting, you’ll want to space them roughly 2-3 feet apart.|
|6 Watts||50 Watt||6W fixtures are generally laid out in a grid such that they are 2’- 3’ off each wall and 4-5’ apart from each other.|
|9 Watts||65 Watts||9W fixtures are generally laid out in a grid such that they are 3’ off each wall and 5-6’ apart from each other.|
|12 Watts||75 Watt||12W fixtures are generally laid out in a grid such that they are about 4-5’ off each wall and about 6-7’ apart from each other.|
|18 Watts||125 Watts||18W fixtures are generally laid out in a grid such that they are 5-6’ off each wall and about 8-10’ apart from each other.|
This fixture is suitable for use in dry or damp locations
When using this fixture in damp locations, it must be installed in a ceiling where it is protected from rain or other moisture by a roof or floor above.
DMX System Diagram
System Diagram: Color Changing - Touch Remote Controlled
For new construction applications, we recommend using aspectLED’s Rough-In Bracket/Plates.
Before installing drywall, layout your light locations and securely fasten the rough-in plate to your joists at each light location. The rough-in brackets have convenient slots in them allowing you to make minor adjustments to the bracket positioning after you’ve mounted them. Run wire (following the conventional or low clearance installation instructions below) to each of your light locations before drywalling.
Before drywalling, double check the location of each light. Once you’ve drywalled, you won’t be able to adjust the positioning.
Instruct your drywallers to cut-out the holes for each light using the rough-in bracket as a template. Then, once drywall is finished, install your lights by following the remainder of the low voltage or line voltage installation instructions below.
Determine a suitable location to install your fixture, power supply, and color changing controls.This will include suitable wire installed between the power supply, the LED light fixture, and any controls. It is important to choose the correct wire for the specific application, this is dependent on voltage drop, amperage rating, and environment. Please consult a voltage drop and wire sizing chart to determine adequate wire size. Using the incorrect wire size will damage your products! If installing wiring in a wall or ceiling, always use in-wall rated wiring. Cut the hole that you’ll install the fixture into.Begin by drawing the appropriately sized cut-out hole on your ceiling using a pencil. Then, using a jab saw (or a drill with a hole saw), make a hole in your ceiling that is the correct size and shape for your light. Run appropriately sized low voltage wire from your central driver location to each light location.You can wire these in series from the power supply to your first light, from your first light to the second, to the third, etc, as shown in System Diagram. But, we do not recommend exceeding 80 watts on a single wire run.
- If you choose to run your own low voltage wire from the driver box to each light, we always recommend using a 2 conductor stranded wire with a voltage rating of at least 300V.
- Please consult a voltage drop and wire sizing chart to determine adequate wire size. Using the incorrect wire size will damage your products! If installing wiring in a wall or ceiling, always use inwall rated wiring.
- You’ll need a little bit of slack in your wire at the light location to allow you to install the light (and to remove it if you ever need to), so be sure to leave about 6-8” of wire sticking out of your hole at the light location. Also, be sure to leave some extra wire at the driver/junction box location, so you have enough slack to neatly organize your wires.
If you ever need to remove the light in order to access your junction box (or anything in the ceiling cavity above), simply grab hold of the sides of the light and gently pull downwards until the light comes about 1/2” down out of the hole. Before pulling the light all the way out of the hole, be sure to get a firm grip on the retention clips, so you can hold them upwards in order to avoid getting your fingers snapped in the springs. Then, pull the light the rest of the way out of the hole and gently let the retention clips back down. Remember, the retention clips have a similar strength to your average mousetrap! Be careful not to snap your fingers inside of the springs!
Have questions or need assistance?
We’re always here to help!
Feel free to contact our electrician’s help desk at (888) 503-1317 option 3, or firstname.lastname@example.org.